DIN Rail Terminal Blocks

The WAGO 2002-402 is a 2-way insulated push-in type jumper bar from the TOPJOB S series (Product Group 22), designed to common adjacent terminals i...

The WAGO 2016-1392 is an end and intermediate plate for TOPJOB S rail-mount terminal blocks, 1 mm thick in orange. It attaches to DIN rails via sna...

The PTI 2,5-PE/L/N from Phoenix Contact is an installation protective conductor terminal block combining PE, phase (L), and neutral (N) connections...

The ATP-STTB 4 from Phoenix Contact is a partition plate designed to electrically isolate and separate adjacent terminal blocks within DIN rail ass...

The WAGO 2216-7604 is a 2-conductor supply terminal block in the TOPJOB S 2216 Series, designed for use in electrical distribution boxes. Push-in C...

The Phoenix Contact D-STTB 2,5 (catalog number 3030459) is a gray end cover designed to terminate and protect DIN rail-mounted terminal block assem...

The Weidmuller A2C is a WDU feed-through terminal block, 2mm2, 800V, 24A, Beige. For general conductor feed-through in control panels. DIN rail mo...

The Phoenix Contact PT 1,5/S-PE/L/N is a 3-row multi-level ground terminal block providing combined PE, L, and N connections in one 3.5 mm wide uni...

The Phoenix Contact UT 4-MT-P/P is a knife-disconnect terminal block from the UT product family, designed for convenient in-circuit isolation with ...

The WAGO 2009-305 is a busbar carrier with end stop function and detachable separator plate, designed for mounting on DIN 35 rail. At 7.5 mm wide, ...

The Phoenix Contact PT 4-PE/3L is a four-level motor terminal block using push-in connection, rated 26 A at 800 V with conductor cross-sections fro...

The Weidmuller WDU 10 is a WDU feed-through terminal block, 10mm2, 1000V, 57A, Blue. For general conductor feed-through in control panels. DIN rail...

The Phoenix Contact FBS 10-6 is a 10-position plug-in bridge designed to parallel adjacent terminal blocks in the CLIPLINE complete system. With a ...

The Phoenix Contact D-PT 10 is a gray end cover designed to close off and protect the ends of terminal block assemblies mounted on DIN rails. At ju...

The Weidmuller WSI 6 is a WSI fuse terminal block, 6mm2, for standard fuse. Integrates fuse protection into the terminal rail. DIN rail mounting.Te...

The Phoenix Contact FBS 2-12 is a 2-position plug-in bridge for use with the CLIPLINE complete terminal block system, bridging adjacent blocks via ...

The Phoenix Contact UCT-TMF 5 is a flat-slot terminal block marker sheet in white (RAL 9010), designed for 5.2 mm pitch terminal blocks and providi...

The Phoenix Contact AP 3 METER is a 1 m transparent PVC cover profile for protecting and covering terminal strips in DIN rail installations. It sna...

The Phoenix Contact PT 4-PE is a protective conductor terminal block providing a low-resistance connection to ground potential via direct DIN rail ...

The ZB 6,LGS:FORTL.ZAHLEN 1-10 is a Phoenix Contact Zack marker strip for labeling modular terminal blocks and electronics modules with tall marker...

The Phoenix Contact PT 16 N BU is a feed-through terminal block rated at 1000 V nominal voltage and 76 A nominal current, designed for high-current...

ZB 5,LGS:FORTL.ZAHLEN 41-50 is a Phoenix Contact Zack marker strip pre-printed with consecutive numbers 41 to 50 for horizontal terminal block iden...

The Phoenix Contact PT 1,5/S-QUATTRO is a multi-conductor feed-through terminal block from the PT product family, rated at 500 V nominal voltage an...

The Phoenix Contact FBS 10-5 BU is a 10-position plug-in bridge designed for the CLIPLINE complete system, enabling simultaneous bridging of up to ...