DIN Rail Terminal Blocks

The Phoenix Contact PTTB 2,5 is a double-level push-in terminal block that integrates two independent circuits in a single 5.2 mm wide unit, rated ...

The Phoenix Contact PT 2,5-3L is a three-level push-in terminal block rated at 500 V and 20 A nominal, accepting conductors from 0.14 mm² to 4 mm² ...

The ZB 5,LGS:FORTL.ZAHLEN 11-20 is a Zack marker strip from Phoenix Contact, designed for clear and durable terminal block identification. This 10-...

The Phoenix Contact PTTB 1,5/S is a double-level push-in terminal block rated at 500 V and 16 A, designed to integrate two independent circuits int...

The Weidmuller Weidmüller 1020000000 is a WDU feed-through terminal block, 1020000000mm2, V, A, Beige. For general conductor feed-through in contro...

The Weidmuller WPE 2,5 is a WPE protective earth terminal block, 2.5mm2, yellow-green. For PE conductor distribution in control panels. DIN rail mo...

The ZB 5,LGS:FORTL.ZAHLEN 1-10 is a Phoenix Contact Zack marker strip for labeling terminal blocks with a 5.2 mm pitch. The 10-section strip is hor...

The Weidmuller 1061200000 WEW 35/2 is an end bracket for W-series terminal block groups, providing a mechanical end stop and preventing lateral mov...

The PTFIX 6/18X2,5 GY is a Phoenix Contact distributor terminal block for power distribution from a single 6 mm² supply line to up to 18 load circu...

The Phoenix Contact PT 4-HESI (5X20) is a fuse modular terminal block for G 5x20 glass or ceramic fuses, rated 500 V and 6.3 A. Its tool-free push-...

The D-UT 2,5/10 is a gray end cover from Phoenix Contact for closing and protecting rows of UT-series terminal blocks on DIN rail assemblies. Manuf...

The ZB 5,LGS:FORTL.ZAHLEN 21-30 is a Phoenix Contact Zack marker strip pre-printed with consecutive numbers 21 through 30 for clear and permanent t...

The Weidmuller WAP 2,5-10 is a WAP W-Series end plate, Beige. Closes off the end of a W-Series terminal block assembly on DIN rail.Technical specif...

The WAGO 2002-1401 is a 4-conductor through terminal block in the TOPJOB S 2002 Series, rated 800 V / 24 A per IEC/EN 60947-7-1 and approved for Ex...

The Phoenix Contact ATP-ST 4 is a partition plate for DIN rail terminal block assemblies, providing physical and electrical separation between adja...

The Schneider Electric LGYT1E24 is a Linergy earth terminal block with 24 connection points, combining screw and screwless (push-in) terminals for ...

The Phoenix Contact D-PT 6 (catalog number 3212044) is an end cover designed to close and protect the open ends of PT 6 terminal block assemblies. ...

The Phoenix Contact PT 6-PE is a protective conductor terminal block for grounding and earthing connections on NS 35/7.5 and NS 35/15 DIN rails. It...

The FBS 50-3,5 BU is a 50-position plug-in bridge from Phoenix Contact, designed to parallel up to 50 terminal blocks in a single step using both b...

The Phoenix Contact PT 2,5 BU is a single-position feed-through terminal block with tool-free push-in connection, rated 800 V and 24 A at a nominal...

The Phoenix Contact UT 2,5 BU is a feed-through terminal block rated at 1000 V nominal voltage and 24 A nominal current, accepting rigid and flexib...

The WAGO 2002-1404 is a 4-conductor through terminal block from the TOPJOB S 2002 Series, rated at 24 A and 800 V per IEC/EN 60947-7-1, designed fo...

The Phoenix Contact PT 4-PE is a protective conductor terminal block providing a low-resistance connection to ground potential via direct DIN rail ...

The Phoenix Contact UT 4 is a single-row feed-through terminal block rated for 1000 V and 32 A, designed for dependable screw-connection wiring on ...